The Foundation of Plumbing Knowledge When Installing a Bathtub
The Foundation of Plumbing Knowledge When Installing a Bathtub
Blog Article
What're your thoughts with regards to How to Install a Bathtub?
Setting up a bathtub isn't specifically brain surgery, however it does need solid plumbing, carpentry, as well as often, tiling skills. Replacing an old bath tub with a new one is also a reasonably hard job. If the old bathtub is conveniently obtainable, the task can move easily; if you have to open up a wall surface to get rid of the old tub as well as place the brand-new tub, the task is much harder. In either situation, the job is within a residence handyman's abilities, although you will need an assistant to vacate the old bathtub and set in the brand-new one. Make certain you have qualified on your own for the work as well as are comfortable trying it. As opposed to employing a professional to take control of a halfway-completed project, it is better to consider using one prior to you start. Opportunities are you may need an expert plumber to make tube links.
This short article will aid you mount a brand-new bath tub in your restroom if you have actually currently acquired a brand-new bathtub as well as do not require to transform the setup of your previous water supply pipelines.
Your devices as well as product checklist must comprise the following:
Removing Old Touches
If you need to replace old faucets with brand-new ones as a part of your setup, after that the first thing you should do is detach the water system. After doing so, turn on the taps to drain any type of water remaining in the system. The procedure of getting rid of the existing taps can be quite bothersome due to the restricted gain access to that is commonly the instance.
Make use of a basin wrench (crowsfoot spanner) or a faucet tool to undo the nut that connects the supply pipelines to the taps. Have a towel prepared for the continuing to be water that will originate from the pipes. When the supply pipelines have been removed, use the exact same device to loosen up the nut that holds the faucets onto the bath/basin. You will certainly require to quit the solitary taps from turning throughout this procedure. As soon as the taps have been gotten rid of, the holes in the bath/basin will certainly have to be cleaned up of any kind of old securing compound.
Prior to moving on to fit the new faucets, contrast the pipeline connections on the old taps to the brand-new faucets. If the old taps are longer than the new faucets, after that a shank adapter is required for the brand-new taps to fit.
Fitting New Touches
If the tails of the new faucets are plastic, then you will certainly require a plastic port to stop damages to the thread. One end of the adapter fits on the plastic tail of the tap and also the various other end supplies a link to the existent supply pipelines.
If you require to fit a monobloc, after that you will certainly call for decreasing couplers, which attaches the 10mm pipeline of the monobloc to the basic 15mm supply pipeline.
Next off, place the faucet in the placing hole in the bath/basin ensuring that the washers remain in area in between the tap as well as the sink. Protect the faucet in place with the supplier provided backnut. Once the tap is safely in place, the supply pipes can be linked to the tails of the taps. The taps can either be connected by utilizing corrugated copper piping or with regular tap adapters. The former type needs to be connected to the faucet finishes initially, tightening up only by hand. The supply pipes can later on be attached to the other end. Tighten both ends with a spanner after both ends have actually been connected.
Setting up the Bathtub
Using the two wooden boards under its feet, place the bath tub in the called for position. The wooden boards are helpful in equally spreading the weight of the tub over the area of the boards as opposed to focusing all the weight onto 4 small factors.
The following objective is to ensure that the bathtub is leveled all round. This can be achieved by examining the level and changing the feet on the bath tub until the spirit level reads level.
To install faucets, fit the bottom of the furthest adaptable tap port to the appropriate supply pipe by making a compression sign up with; then do the very same for the various other tap.
Activate the supply of water as well as inspect all joints and brand-new pipework for leakages as well as tighten them if essential. Fill up the bathtub as well as likewise examine the overflow outlet and the normal outlet for leaks.
Finally, fix the bathroom paneling as defined in the maker's instruction manual. Tiling as well as sealing around the bath tub must wait until the bath tub has been used a minimum of once as this will certainly settle it right into its final placement.
Planning for the Installment
To start with, the supporting framework provided with the bathroom needs to be fitted (if needed) according to the maker's instructions. Next off, fit the taps or mixer to the bath tub. When suitable the tap block, it is necessary to make sure that if the faucet includes a plastic washing machine, it is fitted in between the bathroom and also the taps. On a plastic bath, it is also sensible to fit a sustaining plate under the taps system to prevent pressure on the tub.
Fit the versatile tap adapters to the bottom of both faucets making use of 2 nuts as well as olives (often provided with the tub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the outlet through the hole in the bathroom. Use the nut provided by the supplier to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipeline.
Next off, fit completion of the adaptable overflow pipeline to the overflow outlet. Afterwards, screw the pipe to the overflow face which need to be fitted inside the bathroom. Make sure you utilize every one of the supplied washers.
Attach the trap to the bottom of the waste electrical outlet on the tub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, and also screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a similar manner.The bath should currently prepare to be fitted in its last setting.
Tiling Around the Bathtub
In the location where the bathroom fulfills the floor tile, it is essential to seal the joins with a silicone rubber caulking. This is essential as the fitting can relocate enough to crack a rigid seal, triggering the water to permeate the wall surface in between the bathroom and the tiling, bring about problems with wetness and also possible leakages to the ceiling listed below.
You can choose from a selection of coloured sealants to assimilate your fixtures as well as fittings. They are sold in tubes as well as cartridges, and are capable of securing spaces up to a size of 3mm (1/8 inch). If you have a larger void to fill, you can load it with twists of drenched paper or soft rope. Keep in mind to always fill up the bath tub with water prior to securing, to allow for the motion experienced when the bathtub remains in usage. The sealer can break fairly very early if you do not take into consideration this activity before securing.
Conversely, ceramic coving or quadrant ceramic tiles can be utilized to border the bath or shower tray. Plastic strips of coving, which are easy to use as well as reduce to dimension, are additionally easily readily available on the market. It is advisable to fit the ceramic tiles making use of water-resistant or waterproof glue and cement.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
Hopefully you liked our topic about Tools You Need to Install a New Bathtub . Thank you so much for taking a few minutes to read our blog post. So long as you appreciated our post if you please make sure you remember to pass it around. We treasure reading our article about Tools You Need to Install a New Bathtub .
Plumbing emergencies? Our experts await. Report this page